Description WyreStorm 3-Input In-wall HDBaseT Transmitter The WyreStorm 3-Input In-wall HDBaseT Transmitter sets a new standard for in-wall HDBaseT transmission. The SW-130-TX-US brings features of the WyreStorm range of professional switchers and packs them into a 2-gang form factor. Automatic or manual switching of the 3 connected sources (2 HDMI and USB-C) is possible with the USB-C supporting alt-mode functionality allowing a portable device such as a tablet or phone to be connected and send its content at up to 4K/30. HDCP 2.2 is also supported for the transmission of encrypted content. View QuickStart Guide >> View Specifications >> Features HDBaseT switcher/transmitter for video conference or meeting rooms Compatible with DVI-I and DP v1.3 signals from supported devices Additional 2ch analogue audio input for sending separate stereo audio to RX Automatic or manual CEC triggering for compatible connected screens or projectors Primary power supply via PoH from a supported receiving device (RX-700) Additional power input via DC port on rear via 12v 1A PSU (not included). Port shared with RS-232 input Control options include automatic switching, manual switching & CEC trigger and RS-232 control Compatible with TS-280 touchscreen for control with 12v power outlet US or UK face plate options FEATURES TURNED UP TO 11 However it’s not all about the A/V when it comes to HDBaseT; with increased functionality on all fronts, the SW-130-TX can be used to send power triggers to a compatible connected screen, allowing centralized control and is PoH compatible meaning it can be passively powered over HDBaseT from a compatible receiver. The SW-130-TX can even power & charge a phone or tablet connected to the USB-C port so you don’t run out of juice mid-flow (max. 5v 2A) HDCP 2.2 COMPATIBLE The industry’s latest encryption standard designed to stop the illegal copying & distribution of 4K UHD content; no longer unique to residential solutions WyreStorm presentation switchers are fully compliant with HDCP 2.2, enabling you to de-centralize source devices within an installation. USB 2.0 PASS-THROUGH With this purpose in mind, HDBaseT2.0 affords the addition of USB 2.0 pass-through, offering not only KVM functionality for extension of a keyboard/mouse or touchscreen but also full data transfer capabilities. The SW-130-TX has a USB host port allowing USB device data to be routed into the selected laptop (via HDMI). Going further, it can send USB device data natively through the USB-C port allowing a single cable to be used for A/V and USB device connectivity. In the Box 1x SW-130-TX In-wall Transmitter 1x 4‐pin Phoenix Male Connector 1x USB host cable (Type A-B) 1x Decora face plate (SW-130-TX) 4x Retaining screws (SW-130-TX) 1x Quickstart guide Specifications TRANSMISSION Transmission Encoding: HDBaseT Class C | PAM16 Encoding End to End Latency: 10µs Max. Transmission Bit Rate: 10.2Gbps VIDEO HDMI: (v2.0b) TMDS | 340MHz Maximum Inputs: 2x HDMI In: 19-pin type A1x USB-C In: USB 3.1c Audio/Video (4.5Gbps) Outputs: 1x HDBT out: 8-pin RJ45 Max Pixel Clock: HDMI & HDBaseT: 340MHz Video Resolution (Max): 1920x1080p @60Hz // 2560x1440p @60Hz // 3840x2160p @30Hz 8bit 4:4:4 // 3840x2160p @30Hz 10bit 4:2:0 HDR // 3840x2160p @30Hz 12bit 4:2:2 HDR Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference. Supported Standards: DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100 AUDIO Inputs: 1x Audio In: 3.5mm (1/8in) TRS Stereo // 2ch audio over HDBaseT | 1-way to RX Audio Formats: 2ch PCM | Multichannel up to DTS-X and Dolby Atmos Maximum Sampling Rate: 192KHz Maximum Audio Channels: 32 Audio Return Channel (ARC): Not Supported COMMUNICATION & CONTROL USB Host (HDMI Inputs): 1x Type B host | Maximum data throughput: 190Mbps HDMI: Alt-mode Supported | A/V and USB data from RX USB 3.1c: HDMI | HDCP 2.2 | EDID | CEC | 2ch audio | USB RS-232: 1x RS-232: 4-pin Phoenix | Shared with 12v DC input // Compatible with WyreStorm TS-280 touchscreen via 4-pin phoenix port (only when using PoH) HDCP: Pass-Through, 2.3 Supported EDID: Pass-Through, from RX Consumer Electronics Control (CEC): One-way display trigger to RX Auto Low Latency Mode (ALLM): Supported Variable Refresh Rate (VRR): Supported POWER Power Supply: 12V DC 1A (not included) Max Power Consumption: 7.8W Power-over-HDBaseT (PoH): Supported, 1-way from RX Local Power Supply Input: 4-pin Phoenix
